diff --git a/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-connected-en.webp b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-connected-en.webp
new file mode 100644
index 00000000..2d203cff
Binary files /dev/null and b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-connected-en.webp differ
diff --git a/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-connected-zh.webp b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-connected-zh.webp
new file mode 100644
index 00000000..1640df8a
Binary files /dev/null and b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-connected-zh.webp differ
diff --git a/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-settings-button.webp b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-settings-button.webp
new file mode 100644
index 00000000..5a6cb39f
Binary files /dev/null and b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-settings-button.webp differ
diff --git a/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-en.webp b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-en.webp
new file mode 100644
index 00000000..ad2b4f25
Binary files /dev/null and b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-en.webp differ
diff --git a/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-zh.webp b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-zh.webp
new file mode 100644
index 00000000..9a29c6cd
Binary files /dev/null and b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-zh.webp differ
diff --git a/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-toolbar.webp b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-toolbar.webp
new file mode 100644
index 00000000..88c71da9
Binary files /dev/null and b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-toolbar.webp differ
diff --git a/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-wiring.webp b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-wiring.webp
new file mode 100644
index 00000000..dc979435
Binary files /dev/null and b/docs/hardware/assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-wiring.webp differ
diff --git a/docs/hardware/en/kvm/NanoKVM_Go/finger_robot.md b/docs/hardware/en/kvm/NanoKVM_Go/finger_robot.md
new file mode 100644
index 00000000..a64e121e
--- /dev/null
+++ b/docs/hardware/en/kvm/NanoKVM_Go/finger_robot.md
@@ -0,0 +1,167 @@
+---
+title: Finger Robot
+keywords: NanoKVM Go, Finger Robot, Physical Power Button, Remote Power Control, PWM
+update:
+  - date: 2026-08-19
+    version: v0.1
+    author: Liang Ziyue
+    content:
+      - Added connection, installation, and operation instructions for the Finger Robot
+---
+
+## Introduction
+
+The Finger Robot is a physical-button control accessory for NanoKVM Go. Attach it next to the physical power button of the target device, and NanoKVM Go can drive its arm to press the button. This lets you remotely power the target device on or off, or trigger another action assigned to its power button.
+
+It is useful when the target device is powered off, the operating system is unresponsive, or software-based power control is unavailable.
+
+> Holding a computer power button for an extended period usually forces the computer to power off and may cause unsaved data to be lost. Before operating the Finger Robot, check the press hold duration and the power-button behavior configured on the target device.
+
+## Preparation
+
+Prepare the following items before installation:
+
++ NanoKVM Go;
++ The Finger Robot and the required arm;
++ A full-featured USB Type-C cable;
++ A computer, tablet, or phone that can open the NanoKVM Go web control page.
+
+Make sure NanoKVM Go is powered on and its web control page is accessible.
+
+<!-- ## Port Overview
+
+The Finger Robot provides two ports:
+
++ `PWR`: Connects to the power cable and supplies power to the Finger Robot;
++ `PWM`: Connects to NanoKVM Go and receives arm-control signals.
+-->
+
+<!-- TODO(image): Add a close-up of the Finger Robot PWR and PWM ports and their labels. Suggested path: ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-ports.webp. Insert the image here. -->
+
+## Connect the Devices
+
+Connect the devices as shown below.
+
+![NanoKVM Go and Finger Robot wiring](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-wiring.webp)
+
+<!-- Use the following connection order:
+
+```text
+Power cable → Finger Robot PWR port
+NanoKVM Go → Finger Robot PWM port
+```
+
+To connect the devices:
+
+1. Connect the power cable to the `PWR` port on the Finger Robot.
+2. Connect the `PWM` port on the Finger Robot to NanoKVM Go.
+3. Make sure both connections are secure, and then power on the devices.
+
+Follow the port labels when connecting the cables. Do not swap the `PWR` and `PWM` connections.
+-->
+
+<!-- TODO(image): Add a complete wiring diagram showing the power cable, Finger Robot, and NanoKVM Go. Label PWR, PWM, and the NanoKVM Go connection point. Suggested path: ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-wiring.webp. Insert the image here. -->
+
+## Install the Finger Robot
+
+1. Choose the long arm or short arm based on the distance to the power button and the available installation space.
+2. Place the Finger Robot next to the target device's power button. Align the arm with the center of the button when pressed.
+3. Make sure the released arm does not remain in contact with or hold down the power button.
+4. Clean and dry the mounting surface, and then attach the Finger Robot securely.
+5. After mounting it, test with a low press strength first and increase the level only when necessary.
+
+<!-- TODO(image): Add an installation example showing the Finger Robot attached next to a computer power button. Mark the alignment between the arm and button. Suggested path: ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-installation.webp. Insert the image here. -->
+
+## Enable the Feature
+
+1. Log in to the NanoKVM Go web control page in a browser.
+2. Click the Settings icon on the floating toolbar.
+
+![Open the NanoKVM Go settings page](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-settings-button.webp)
+
+3. Open `Settings → Appearance`.
+
+![Enable Finger Robot in the Appearance settings](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-en.webp)
+
+4. Turn on the `Finger Robot` switch.
+
+<!-- TODO(image): Add an English screenshot of the Settings → Appearance → Finger Robot switch. Suggested path: ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-en.webp. Insert the image here. -->
+
+After the switch is enabled, a Finger Robot icon appears on the floating toolbar. Click the icon to open the Finger Robot configuration panel.
+
+![Open the Finger Robot configuration panel](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-toolbar.webp)
+
+<!-- TODO(image): Add an English screenshot of the Finger Robot icon on the floating toolbar and mark the entry. Suggested path: ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-toolbar-en.webp. Insert the image here. -->
+
+## Configuration and Operation
+
+The Finger Robot configuration options are shown below.
+
+![Finger Robot configuration options](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-connected-en.webp)
+
+<!-- TODO(image): Add an English screenshot of the Finger Robot configuration panel. Suggested path: ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-en.webp. Insert the image here. -->
+
+### Connection Status
+
+The top of the panel shows the Finger Robot connection status. If the page reports that the Finger Robot is not connected, check whether the cables are connected correctly.
+
+Test the press operation only after the connection succeeds. The operation buttons at the bottom of the panel are unavailable while the Finger Robot is disconnected.
+
+### Select the Arm
+
+Select `Long Arm` or `Short Arm` to match the arm that is physically installed. This setting affects the Finger Robot's movement range and must match the actual arm.
+
+After changing the arm type, check its alignment with the power button again and begin testing with a low press strength.
+
+### Adjusting the Press Stroke
+
+The Press Stroke offers 1 to 5 levels. The higher the level, the greater the press stroke of the swing arm.
+
+For the first test, it is recommended to start from level 1. If the swing arm does not fully press the power button, increase the level by one step and retest. Do not directly use a high level to avoid unnecessary stress on the swing arm, the button, or the adhesive points.
+
+### Set the Press Hold Duration
+
+`Press Hold Duration` controls how long the arm remains pressed during each operation. The value is measured in milliseconds (ms).
+
++ A short press can power on the target device or trigger the shutdown, sleep, or other action assigned to its power button by the operating system;
++ A longer press may force the target device to power off.
+
+The exact behavior depends on the target device hardware and operating-system settings. Begin with a short duration and adjust it only when necessary.
+
+### Set the Press Speed
+
+`Press Speed` controls how quickly the arm presses and releases. After first installation or position adjustment, use a slower speed so that you can check whether the arm reaches the power button correctly.
+
+### Perform a Press
+
++ Click `Press Once` to perform one press-and-release cycle using the selected arm type, press strength, hold duration, and speed;
++ Click `Release Now` to end the current hold and release the arm. Use this button if the configured hold duration is unsuitable or you need to stop a press early.
+
+<!-- TODO(image): Add an English screenshot or animation showing a successful connection and one completed press. Suggested path: ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-press-demo-en.webp (or GIF). Insert the image here. -->
+
+## First Test
+
+After installation, test the Finger Robot in the following order:
+
+1. Make sure the top of the panel shows that the Finger Robot is connected.
+2. Select the arm type that matches the installed arm.
+3. Set the press strength to level 1 and select a slow press speed.
+4. Set a short press hold duration.
+5. Click `Press Once` and check whether the arm is aligned with and fully presses the power button.
+6. If the power button is not triggered, check the mounting position first and then increase the press strength one level at a time.
+7. After both pressing and releasing work correctly, adjust the hold duration and speed for the target device as needed.
+
+Observe the Finger Robot next to the device during initial testing. Use it unattended only after confirming that the configuration works correctly.
+
+## Troubleshooting
+
+### The Arm Moves but Does Not Trigger the Power Button
+
++ Make sure the selected long or short arm matches the installed arm;
++ Check that the arm is aligned with the center of the power button;
++ Make sure the Finger Robot is attached securely;
++ Increase the press strength one level at a time, and test after each adjustment.
+
+### The Arm Does Not Release Promptly
+
+Click `Release Now` first. Then reduce the press strength or press hold duration and check the installation position again. Continue using the Finger Robot only after confirming that the arm releases correctly.
diff --git a/docs/hardware/en/sidebar.yaml b/docs/hardware/en/sidebar.yaml
index df15b248..66516bc4 100644
--- a/docs/hardware/en/sidebar.yaml
+++ b/docs/hardware/en/sidebar.yaml
@@ -557,6 +557,8 @@ items:
             file: kvm/NanoKVM_Go/user_guide.md
         -   label: Resolution and EDID Settings
             file: kvm/NanoKVM_Go/resolution.md
+        -   label: Finger Robot
+            file: kvm/NanoKVM_Go/finger_robot.md
         -   label: MCP
             file: kvm/NanoKVM_Go/mcp.md
         -   label: Memory Fabric
diff --git a/docs/hardware/zh/kvm/NanoKVM_Go/finger_robot.md b/docs/hardware/zh/kvm/NanoKVM_Go/finger_robot.md
new file mode 100644
index 00000000..6eaefa4a
--- /dev/null
+++ b/docs/hardware/zh/kvm/NanoKVM_Go/finger_robot.md
@@ -0,0 +1,157 @@
+---
+title: 手指机器人
+keywords: NanoKVM Go, 手指机器人, 物理电源键, 远程开关机, PWM
+update:
+  - date: 2026-08-19
+    version: v0.1
+    author: Liang Ziyue
+    content:
+      - 新增手指机器人连接、安装与操作说明
+---
+
+## 简介
+
+手指机器人是 NanoKVM Go 的物理按键控制配件。将手指机器人粘贴在被控设备的物理电源键旁边后，NanoKVM Go 可以控制摆臂按下电源键，从而远程开机、关机或执行被控设备为电源键设置的其他操作。
+
+该配件适用于被控设备已经关机、操作系统无响应，或无法通过软件方式控制电源的场景。
+
+> 长时间按住电脑的电源键通常会触发强制关机，可能导致未保存的数据丢失。执行操作前，请确认按下保持时间和被控设备的电源键行为设置。
+
+## 使用前准备
+
+开始安装前，请准备：
+
++ NanoKVM Go；
++ 手指机器人及所需摆臂；
++ 全功能 Type-C 数据线；
++ 可以打开 NanoKVM Go 网页控制端的电脑、平板或手机。
+
+请先确认 NanoKVM Go 已正常开机，并且网页控制端可以正常访问。
+
+<!-- ## 认识接口
+
+手指机器人提供以下两个接口：
+
++ `PWR`：连接电源线，为手指机器人供电；
++ `PWM`：连接 NanoKVM Go，接收摆臂控制信号。
+
+TODO(image): 补充手指机器人 PWR、PWM 接口及丝印特写。建议保存为 ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-ports.webp，并在此处插入图片。 -->
+
+## 连接设备
+
+按照下图连接好设备。
+
+![NanoKVM Go 与手指机器人接线示例](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-wiring.webp)
+
+<!-- 连接顺序如下：
+
+```text
+电源线 → 手指机器人 PWR 接口
+NanoKVM Go → 手指机器人 PWM 接口
+```
+
+具体步骤如下：
+
+1. 将电源线连接到手指机器人的 `PWR` 接口。
+2. 将手指机器人的 `PWM` 接口连接到 NanoKVM Go。
+3. 检查两个接口是否插接牢固，然后为设备通电。
+
+请按接口丝印连接线缆，不要将 `PWR` 和 `PWM` 接反。 -->
+
+<!-- TODO(image): 补充电源线、手指机器人和 NanoKVM Go 的完整接线图，并标出 PWR、PWM 及 NanoKVM Go 连接位置。建议保存为 ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-wiring.webp，并在此处插入图片。 -->
+
+## 安装手指机器人
+
+1. 根据手指机器人与电源键之间的距离和安装空间，选择长摆臂或短摆臂。
+2. 将手指机器人放在被控设备的电源键旁边，调整位置，使摆臂按下时对准电源键中心。
+3. 确认摆臂松开时不会持续接触或压住电源键。
+4. 清洁并擦干粘贴位置，然后将手指机器人固定牢靠。
+5. 固定后先使用较低的按压力度进行测试，再根据实际情况逐档调整。
+
+<!-- TODO(image): 补充手指机器人粘贴在电脑物理电源键旁边的安装示例，并标出摆臂与按键的对准位置。建议保存为 ../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-installation.webp，并在此处插入图片。 -->
+
+## 开启功能
+
+1. 在浏览器中登录 NanoKVM Go 网页控制端。
+2. 点击悬浮栏中的设置图标。
+
+![打开 NanoKVM Go 设置页面](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-settings-button.webp)
+
+3. 依次进入 `设置 → 外观`。
+
+![在外观设置中开启手指机器人](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-switch-zh.webp)
+
+4. 打开 `手指机器人` 开关。
+
+开关打开后，网页控制端的悬浮栏中会显示手指机器人图标。点击该图标，即可打开手指机器人配置菜单。
+
+![打开手指机器人配置菜单](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-toolbar.webp)
+
+## 配置与操作
+
+手指机器人的配置选项如下图所示。
+
+![手指机器人配置选项](./../../../assets/NanoKVM/go/finger_robot/nanokvm-go-finger-robot-panel-connected-zh.webp)
+
+### 连接状态
+
+菜单顶部显示手指机器人的连接状态。如果页面显示“手指机器人未连接”，请先检查接线是否正确。
+
+连接成功后再测试按压操作。未连接时，菜单底部的操作按钮不可用。
+
+### 选择摆臂
+
+根据实际安装的摆臂选择 `长摆臂` 或 `短摆臂`。该选项会影响手指机器人的运动范围，必须与实际使用的摆臂一致。
+
+切换摆臂类型后，请重新检查摆臂是否对准电源键，并从较低的按压力度开始测试。
+
+### 调整按压行程
+
+`按压行程` 提供 1 至 5 档。档位越高，摆臂的按压行程越大。
+
+首次测试建议从 1 档开始。如果摆臂没有完全按下电源键，可每次提高一档并重新测试。不要直接使用过高档位，以免摆臂、按键或粘贴位置承受不必要的压力。
+
+### 设置按下保持时间
+
+`按下保持时间` 用于设置每次按压时摆臂保持按下状态的时长，单位为毫秒（ms）。
+
++ 普通短按可用于开机，或触发操作系统为电源键配置的关机、睡眠等操作；
++ 较长的保持时间可能触发被控设备强制关机。
+
+具体行为由被控设备的硬件和操作系统设置决定。请先使用较短的保持时间测试，再按实际需要调整。
+
+### 设置按压速度
+
+`按压速度` 用于调整摆臂按下和松开的运动速度。首次安装或重新调整位置后，建议先选择较慢的速度，便于观察摆臂是否准确按到电源键。
+
+### 执行按压
+
++ 点击 `按压一次`，手指机器人会按照当前的摆臂类型、按压力度、保持时间和按压速度完成一次按下和松开动作；
++ 点击 `立即松开`，手指机器人会结束当前按住状态并松开摆臂。当保持时间设置不合适或需要提前停止按压时，可使用此按钮。
+
+## 首次测试
+
+安装完成后，建议按以下顺序测试：
+
+1. 确认菜单顶部显示手指机器人已经连接。
+2. 选择与实际安装一致的摆臂类型。
+3. 将按压力度设为 1 档，并选择较慢的按压速度。
+4. 设置较短的按下保持时间。
+5. 点击 `按压一次`，观察摆臂是否对准并完整按下电源键。
+6. 如果未能触发电源键，先检查安装位置，再逐档增加按压力度。
+7. 确认按压和松开均正常后，再按被控设备的实际需要调整保持时间和速度。
+
+测试时请在设备旁观察手指机器人的动作，确认配置正确后再进行无人值守的远程操作。
+
+## 常见问题
+
+### 摆臂动作但没有触发电源键
+
++ 检查长摆臂或短摆臂选项是否与实际安装一致；
++ 检查摆臂是否对准电源键中心；
++ 确认手指机器人粘贴牢固；
++ 从低到高逐档增加按压力度，每次调整后重新测试。
+
+### 摆臂没有及时松开
+
+先点击 `立即松开`，然后减小按压力度或按下保持时间，并重新检查安装位置。确认摆臂能够正常松开后，再继续使用。
diff --git a/docs/hardware/zh/sidebar.yaml b/docs/hardware/zh/sidebar.yaml
index 3c65cc0c..6f308a13 100644
--- a/docs/hardware/zh/sidebar.yaml
+++ b/docs/hardware/zh/sidebar.yaml
@@ -558,6 +558,8 @@ items:
             file: kvm/NanoKVM_Go/user_guide.md
         -   label: 分辨率与 EDID 设置
             file: kvm/NanoKVM_Go/resolution.md
+        -   label: 手指机器人
+            file: kvm/NanoKVM_Go/finger_robot.md
         -   label: MCP 功能
             file: kvm/NanoKVM_Go/mcp.md
         -   label: 记忆织网